Car power amp for subwoofer 180W into 8ohm

JAKUB_G

New member
This I made for my friend, who wants little amp to feed his sub-woofer in the car.
The switching power supply is based on SG3524 - data-sheet circuit. Feedback is with optotransistor, that´s why is SMPS very bump. The effectiveness of SMPS achieves something more then 80%.

Full power: 180W/8ohm
min. load impedance : 8R
input voltage for full power: 0,35V RMS
transmitted band: 30-150Hz
voltage in the output of SPS: +-55V
effectiveness: cca 80%
max off-take current: 23A@12V - 150W/8R
fuse protection: 20A auto-fuse
dimensions: 150*210*75

I hope, it will appeal to You.
 

Attachments

  • PB060085.JPG
    PB060085.JPG
    328.4 KB · Views: 401
  • PB080009.JPG
    PB080009.JPG
    467 KB · Views: 293
  • PB080006.JPG
    PB080006.JPG
    454.3 KB · Views: 276
  • PB080007.JPG
    PB080007.JPG
    465.3 KB · Views: 189
  • PB080004.JPG
    PB080004.JPG
    487.6 KB · Views: 311
  • PB080002.JPG
    PB080002.JPG
    308.3 KB · Views: 177
  • PB060086.JPG
    PB060086.JPG
    407.4 KB · Views: 165
  • PB020075.JPG
    PB020075.JPG
    326.1 KB · Views: 212
  • PB080091.JPG
    PB080091.JPG
    338.1 KB · Views: 147
  • PB080010.JPG
    PB080010.JPG
    482 KB · Views: 238
  • PB080088.JPG
    PB080088.JPG
    226.3 KB · Views: 147
  • PB080092.JPG
    PB080092.JPG
    313.3 KB · Views: 139
  • PB060087.JPG
    PB060087.JPG
    439.4 KB · Views: 155

Corvett

New member
SMPS Car

Very nice car amplifier.

Is there a schematics for project and PCB will be published?


Is this only for sub woofer amplifier? can be used for good sounding amplifier?

Transformer? is it accessible to DIY like me?

Amplifier technical data please, one channel or two?

Thank you

Very well designed PCB :D
 
Last edited:

JAKUB_G

New member
This is only one channel amplifier, the crossover is not switch-able so it´s fixed. It was doing for specific loudspeaker.
T can only post schematic of SPS, because amplifier and crossover are just in my mind :D.
Yes transformer is made by me...
 

SaintGP

New member
hi Buddy

This is just what i was looking for.

Could you please share schematic and partslist please

Thanking you in advance
 

Corvett

New member
Schematics

Still waiting for PCB layout and transformer construction details


I also want to make one
 

JAKUB_G

New member
Sure, but I havent written schematic jet. With transformer it will be little problem because I really dont remember.. I have it somewhere written down...
 

Corvett

New member
Jakub_G

I asked for schematics long time ago


Are you going to share PCB files + Schematics or not? ::SD
 

JAKUB_G

New member
Sorry, I wrote the reasons in one of my thread in classAB. Yes, you asked, I know, but, I have to finish one... and than do something else.
 

radio

New member
Hi JAKUB_G!
I and many others expected to see the PCB pattern here!
Interesting because project so please display the schematic and the PCB!
A big thank you in advance!
P.S.
Made me what your 100W High-End Amplifier and I am very happy with it!
 

giololucas

New member
This I made for my friend, who wants little amp to feed his sub-woofer in the car.
The switching power supply is based on SG3524 - data-sheet circuit. Feedback is with optotransistor, that´s why is SMPS very bump. The effectiveness of SMPS achieves something more then 80%.

Full power: 180W/8ohm
min. load impedance : 8R
input voltage for full power: 0,35V RMS
transmitted band: 30-150Hz
voltage in the output of SPS: +-55V
effectiveness: cca 80%
max off-take current: 23A@12V - 150W/8R
fuse protection: 20A auto-fuse
dimensions: 150*210*75

I hope, it will appeal to You.

Great assembly!
Where did you find this case heatsink?
Regards.
 

JAKUB_G

New member
Hello everybody. Im back. I didnt post the PCB layout and documentation, because there was some problem with this amp. I will sove it soon, i hope. But now Im working on swiching power supply (DC/DC convereter) about 250-300VA to supply any ampiefier.
 

DCPreamp

New member
Wow, what a beautiful project! Congratulations on a job well done!

I guess like everyone else, I'd love to see documentation of the project, supply list (like the heatsink, transformer specifics, etc.), and construction details. But, there's no hurry. I understand life is busy and unlike others, I don't expect anything. I appreciate anything you have to offer, but it's totally up to you to provide details. If you wish not to, I totally understand and won't ever push.

Thank you for everything you already posted!
 
Top